Early CB350 twins had an oil sealing issue at the valve adjustment eccentric shafts. Though later models didn't have this issue, look out for it anyway. You might have early cam bearings. The later bearings should have tapered holes cut on their backsides to accommodate the shaft's sealing o-rings. Early ones, oddly, didn't have this machining.
Despite forum insitence, you don't have to "clock" the piston rings, that is something no pro mechanic does, including well-known 350 racer Stan Lipert (catch his pix and videos on Facebook), and myself. The cylinders will install easier if the ring gaps are lined up, and each ring will rotate in a random fashion once the engine is running anyway. If you still would rather clock, it won't hurt anything, but neither is it necessary.
Grease the connecting rod small ends before putting in the piston pins. The best grease for this (and for the cam-to-bearing interface) is Honda's own moly grease. It comes in a red and white tube. I have used it for eons on all kinds of Honda engines.
Honda never chamfered the stud pass-through holes in the cylinder assembly. I do it to ensure aluminum shavings from the studs don't fall into the engine while the cylinder is being lowered on. I usually carefully chamfer the base gasket once it is attached to the cylinder bottom also.
The piston pin circlips, once clicked into place, should be rotated a few degrees using a cotter pin puller as a double-check that they are fully seated. When installing them, try not to distort them and make them permanently out-of-round. If you do, replace them.
The best engine gaskets are Cometic. Order the standard 0.042" thickness composite type head gasket in the standard diameter, and the standard 0.020" paper base gasket. And it is an order situation, not a purchase online situation.
Coat the head gasket with Gaskacinch, lightly on both sides of the gasket, and let dry at least half an hour before installing the gasket onto the engine. This is classic Honda dealer mechanic technique.
Lightly stone the cylinder head, cam box and cylinder assembly gasket surfaces.
Don't put any gasket sealer on the base gasket, as that will cause it to fail.
Despite forum advice, do not put Hondabond 4 or any other sealer on the outside edges of the engine's This will make them more likely to squirm out of place, not less.
Grease the inner diameter of all oil seals.
Speaking of oil seals, there are seal kits such as on 4into1. Their quality is not the same as Honda's, but they are pretty much all there is now. There is also NOS Parts Now, CMSNL also.
Replace the tach drive oil seal. It's a bit of a job, but important.
For ease of engine assembly, I like to 3M 77 aerosol paper glue the base gasket to the cylinder base to keep it out of harm's way during cylinder install. This is not gasket sealer, it is simply using mat (picture matting) glue to keep the vulnerable base gasket from getting damaged while handling the cylinders. Use it sparingly. I use a Q-Tip on the cylinder assy.
Don't forget those cylinder flange o-rings.
Honda's piston ring compressors are still available and are exceptionally good, but not completely necessary. They are used together with piston blocks, pieces of wood. The factory Honda ones were aluminum).
Set the valve clearances 0.001" over the factory spec to improve this engine's low-speed rideability.
The valve followers on this engine are chrome-plated. That chrome comes off over time. You must catch it before too much comes off, to prevent subsequent camshaft damage.
The hash marks on the valve adjustment eccentric shafts need to point outward, away from the spark plugs. Ignoring this will alter the valve timing and thus affect engine behavior.
If you find that the eccentric adjusters rotate a full 360 degrees or more, this is a sign of excessive wear somewhere in the valve train. Usually, it is the followers (rocker arms) that are damaged. They are very vulnerable.
One of the hazards of using an automotive machine shop to do your cylinder head work is that this engine's eccentric adjusting system will tolerate only very careful, light valve seat machining. Excessive seat machining will remove the engine's built-in valve clearance. If stainless steel valves are used, they can be tipped to compensate. The stock valves cannot, requiring the rockers to be ground instead.
Whatever method you use to adjust the cam chain, static of course, it must put the crankshaft where all the chain's tension is at the front of the engine and all the slack is toward the back. In addition, I use a trick where I will double the cam chain tensioner gaskets temporarily while setting the tensioner, then remove the extra gasket and bolt the tensioner back on. This preloads the tensioner slightly.
Seal the intake manifolds to the head using Hondabond 4, the same stuff you sealed the crankcase halves with. Yes, this is in addition to the gaskets (put on both sides). This engine, like several Hondas, has trouble with vacuum leaks in this area.
Don't use sealer anywhere else, and avoid using silicone sealer on the Honda engine.
Put new o-rings on the valve inspection caps (and lightly grease them). New o-rings will not only improve oil tightness, it will prevent the caps from seizing to the cambox, which they frustratingly are prone to do.
If the manifold clamps bottom out, this is a sign that the manifolds are collapsing, which is common. The clamps themselves are often stretched also. Putting small washers on the screws can overcome deformed clamps, or replace them.
Set the spark plug gaps to 0.032".
Confirm that the centrifuge pressure valve located in the clutch cover moves in and out freely. Be sure to clean out the centrifuge thoroughly also.
The manual shows a 6mm bolt (#14 on the parts diagram) that you unscrew to check for top end oiling once the engine has started.
Adjusting the carburetors on this bike is perhaps the most difficult of any Honda of the period. Not only the throttles must be synced, but the cables also.
There is no such thing as "break-in" on a Honda engine's top end that has received quality machining, parts and assembly. By the end of the first test ride, the engine will have as much cylinder compression as it will ever have. This is because the top piston ring has a tin coating on it. Get cylinder head work also, as that will contribute even more to engine compression.
This engine's drain plug design is really unfortunate. The part is likely chewed up all to hell because its design makes it seize in the crankcase. I use a special heavy-duty 6-point socket just for this part.
If you hear noises on starting, whirr..bang, or screech, screech, that is the starter clutch. It is the weakest part of this engine. Unfortunately all the parts to rebuild it are long gone from Honda. The few I have rebuilt in the past several years have been with good used parts I was fortunate enough to find. At least it is easy to get to, but it deteriorates quickly and if allowed to stay that way it will ruin the alternator rotor, in addition to its effect on electric starting.
I am not talking about the starter motor itself. That part is very durable and if needed, easily rebuilt. There are even aftermarket rebuild kits (but not from Honda) available.
Check your crankcase ventilation. Excessive crankcase pressure will create oil leaks.
It was a common mod back in the day to boost the charging system. Easily done at the canon plug. Replacing the rectifier (looks like a french fry cutter) is a good idea even if it hasn't gone bad yet, because updating it from its selenium design will free up more charge current.
What a hassle that fuel tank crossover hose is, huh? Messy. Never liked dealing with that.
Deal with tank rust. You can run inline fuel filters, and it is recommended.
Make sure the carburetor diaphragms do not have holes, tears or even creases. Replacement diaphragms are available from JBM Industries, and elsewhere. You buy them from JBM by dimensions, so you must measure yours. See their online instructions. Kind of tricky to replace.
Try to use only factory float valves in these carbs. Expensive, but the others are far less reliable.
I don't use carburetor rebuild kits. I would rather use still-good fifty-plus year old factory metering parts than new poor quality Chinese ones.
The needle jet and jet needle are probably very worn in your carbs. Since they control 80 percent of the carbs' fuel mixture, this can be a significant problem. The pilot screws have possibly deformed the carb bodies (castings) also. Honda's 350 and 450 twins of the period run frustratingly rich for these and other reasons.
I have found that replacing the slide springs with those from an 80s DOHC 750 carb improves intermediate throttle carburetion.
You probably have an electronic ignition on your bike. If not, you're in for an education. The factory ignition can be made to work excellently, but it is far from intuitive how to do so. Even career mechanics had to teach themselves. Try to use only factory points if keeping the stock ignition. The aftermarket ones are not very good. See my website articles.
Another thing requiring some skill is properly adjusting the front brake on the CL model's double-leading shoe design. It's a little fiddly.
The connecting rods are copper-plated as part of an electro-hardening process for the two ends (large and small ends) that needed to be hard, yet the main body of the rod be softer and more flexible to resist breaking. The rod is packed in some chemical and the copper plating makes it resist hardening.
This engine has a plunger type oil pump because of its rolling element type main bearings that require much less oil pressure than do plain type. However, the cams are themselves in plain bearings and as such may not get the oil pressure they would best get, though they get adequate flow.
The similar 450 engine got a larger plunger type pump at some time in its history, and there are aftermarket upgrades for both it and the 350.
Like the 450, the 350's top end oiling goes through the clutch cover and up a cylinder stud.
There are aftermarket needle bearing kits for both of these engines' cams.
There is a lot of performance work being done on the 350 engine.
350 twin pistons were commonly used in 750 fours for high performance, the origin in fact of the famous "836" kit.
Some of the 350's transmission and clutch parts were used in the inaugural 500cc four of 1971-1973, Honda's second four cylinder roadbike.
The 350's carburetors were derived from those used in Honda's two-cylinder cars, including the penchant for vacuum diaphragm failure. The 350 also became the poster boy for ultra-sensitivity to throttle changes that initially gave constant velocity carburetors a bad reputation.
The 350 twin's charging system employs (at the same time) two kinds of charging control, a shunting type voltage regulator and in addition, a two-stage alternator whose output increases (via the switch) when the headlight is turned on. This latter feature is the one you modify to boost daytime charging.
I was probably 15 years old when I first saw a CB350. I remember thinking how big and brawny the bike looked!
Honda's 350 and 450 twins of course escaped the troubles the early fours would experience of fast-wearing primary (crankshaft to clutch) chains. The 350 and 450 have gear primary so avoided that.
There must have been virtually no one who regularly cleaned out those oil centrifuges.
I would estimate that 90 percent of poor running on a 350 is due to ignition issues.
The venerable 350 twin was like the original VW Beetle in one interesting way. The VW when the battery became weak would illuminate one of its headlight brighter than the other. Similarly, the 350 when low on voltage would feed one of its ignition coils more energy than the other, with the expected result.
Stan Lipert does a dual-plug modification on his racing 350s. The benefit is cylinder compression can be increased more than would otherwise be possible, for better drive out of corners.